Firing Order - 3.9L - 1-6-5-4-3-2 5.2L and 5.9L - 1-8-4-3-6-5-7-2 Spark Plug Gap - Same For All Motors 89-94 and 96-98 - 0.035 95 - 0.030 Torque Specs - (** See Procedure) Intake Manifold Bolts - 3.9L 5.2L and 5.9L - 12Ft-Lbs Camshaft Sprocket Bolt - 35Ft-Lbs Converter Y-Pipe-To-Exhaust Manifold - 25Ft-Lbs Crankshaft Damper Bolt - 135Ft-Lbs Cylinder Head Bolts - 105Ft-Lbs** Engine Mount Nuts - 75Ft-Lbs Exhaust Manifold - 25Ft-Lbs Exhaust Manifold-To-Cylinder Head - 25Ft-Lbs Exhaust Pipe-To-Manifold Junction Flange - 19Ft-Lbs Fan Blade Assembly-To-Viscous Fan Clutch - 17Ft-Lbs Fan Shroud Mounting Nuts - 95In-Lbs Flywheel-To-Driveplate - 55Ft-Lbs Heat Shields - 55In-Lbs Lifter yokes - 200In-Lbs Main Cap Bolts - 85Ft-Lbs Oil Pan Bolts - 200In-Lbs Oil Pump Bolts - 30Ft-Lbs Plenum Pan Bolts - 84In-Lbs Radiator Mounting Bolts - 95In-Lbs Rocker Arm Retaining Bolts - 21Ft-Lbs Rocker Shaft Bolts - 200In-Lbs Starter Bolts - 50Ft-Lbs Thermostat Housing Bolts - 200In-Lbs Throttle Body-To-Intake Manifold - 200In-Lbs Timing Cover Bolts - 30Ft-Lbs Torque Converter-To-Drive Plate - 23Ft-Lbs Transmission Support Bolts - 50Ft-Lbs | Rocker Shaft Bolts - 200In-Lbs Starter Bolts - 50Ft-Lbs Thermostat Housing Bolts - 200In-Lbs Throttle Body-To-Intake Manifold - 200In-Lbs Timing Cover Bolts - 30Ft-Lbs Torque Converter-To-Drive Plate - 23Ft-Lbs Transmission Support Bolts - 50Ft-Lbs Valve Cover Bolts - 95In-Lbs Water Pump Bolts - 30Ft-Lbs Water Pump Pulley Bolts - 20Ft-Lbs Yoke Retainer - 200In-Lbs Manual Tranmission - Back-Up Light Switch - NP-2500 - 15Ft-Lbs AX-15 - 27Ft-Lbs Transmission Assembly - Transmission-To-Clutch Bell Housing - 50Ft-Lbs Crossmember - 30Ft-Lbs Transmission Mount-To-Crossmember - 50Ft-Lbs Universal Joint Straps - 170In-Lbs Clutch - Pressure Plate - 5/16 Inch Bolts - 20Ft-Lbs 3/8 Inch Bolts - 30Ft-Lbs Master Cylinder - Fluid Reservoir - 40In-Lbs Slave Cylinder - 17Ft-Lbs Automatic Transmission - Park/Neutral Switch - 25Ft-Lbs Torque Converter - 9.5 Inch 3 Lug Converter - 40Ft-Lbs 9.5 Inch 4 Lug Converter - 55Ft-Lbs 10.0 Inch 4 Lug Converter - 55Ft-Lbs 10.75 Inch 4 Lug Converter - 23Ft-Lbs Driveline - 1/4 Inch Bolts - 14Ft-Lbs 5/16 Inch Bolts - 25Ft-Lbs |
**Cylinder Head Installation - Place head gasket onto the engine block, then place the head onto the gasket and engine block.Tighten in sequence, all the head bolts to 50Ft-Lbs. Then repeat in sequence again tightening the bolts to 105Ft-Lbs. 7 - 3 - 1 - 5 8 - 4 - 2 - 6 |
